Repair and modernisation: NILES DP1 S2
• Running-in and operational checks completed in all modes;
The photographs show this particular machine.
DP-1/S2 is a face-turning lathe manufactured by WMW NILES, Germany, designed for machining end and cylindrical surfaces on cast-iron and steel products using high-speed steel or carbide-insert tools. It is a universal machine of normal accuracy.
Used for rough and finish turning of flange, cylindrical and conical surfaces, hole enlargement and boring, facing and thread cutting, including metric, imperial and module threads, in one-off and small-batch production.
Accuracy in finish turning/according to GOST: tolerance grade IT 6 / 2-С. If required, workpieces with an outside diameter greater than 2500 mm can be machined by installing the machine on additional foundation plates; flanges with a diameter of 3500 mm have been machined in this arrangement. With a tailstock and steady rests, cylindrical rotational parts up to 10000 mm long can be machined.
• A wide range of spindle speeds and feeds ensures productive machining, while the rigidity of the cast bed provides a fine surface finish.
• Metric, inch and module threads can be cut.
• The tool holder design improves clamping stability.
• Special precision spindle bearings require no adjustment during operation, providing the necessary rigidity and high machining accuracy.
• The kinematic chain and the overall machine construction ensure high reliability.
• Improved electrical reliability through modern electrical control components and installation of new wiring and cable routes.
• An operator panel further improves reliability during operation.
Machine weight – 19 tonnes.
| Technical specifications: | |
|---|---|
| Centre height above the foundation plates, mm. | 1250 |
| Swing diameter over the foundation plates, mm. | 2480 |
| Maximum workpiece weight mounted between centres, kg | 10000 |
| Maximum faceplate torque, Nm. | 20000 |
| Drive power / rated connected load, kW | 45 / 55 |
| Tool shank cross-section, mm. | 50x50 |
| Operating voltage | 3×380 V / 3 phases / 50 Hz / 118 A |
| Spindle head | |
| Working spindle diameter at the front bearing, mm. | 240 |
| Working spindle bore, mm. | 100 |
| Internal taper 1, mm | 10 |
| Number of faceplate speeds | 18 |
| Spindle speed series ratio | 1,28 |
| Speed range, rpm | |
| - Speed series 1 | 55 – 180 |
| - Number of spindle speeds 2 | 4,5 – 224 |
| - Number of spindle speeds 3 | 5,6 – 280 |
| - Number of spindle speeds 4 | 7,1 – 355 |
| Faceplate | |
| Faceplate outside diameter, mm. | 1250 |
| Minimum clamping diameter for external/internal clamping, mm. | 180/400 |
| Maximum clamping diameter for external/internal clamping, mm. | 1000/1250 |
| Longitudinal slide — bed length, mm. | 1200 |
| Cross slide, mm. | 750 |
| Extended cross slide, mm. | 630 |
| Tool feed slide, mm. | 180 |
| Swing over the bed, mm. | 1250 |
| Swing diameter over the longitudinal slide. | 800 |
| Feed mechanism | |
| Number of feeds independent of spindle speed, pcs | 18 |
| Spindle-speed-independent feed range, mm/min | 0,5...180 |
| Number of feeds dependent on feed drive speed | 24 |
| Overall range of spindle-speed-dependent feeds, mm/rev | - 0,0056...16 - 0,0045...12,5 |
| Longitudinal and transverse rapid traverse, mm/min | 5000 |
| Threading device (standard pitch) | |
| - Metric thread, mm. | 1...60 (48) |
| - Imperial thread, lead | 24...0,5 |
| - Module thread, mm | 0,5...20 |
| Large-pitch threading device (150%) | |
| - Metric thread, mm. | 150 |
| - Imperial thread, lead | 3 / 16 |
| - Module thread, mm. | 44 |









