Major overhaul and modernisation: 16К20, distance between centres 1000
Overhaul and digital readout installation
Work carried out
We built a new electrical cabinet and replaced the wiring. Optical scales and a digital readout were installed.
Result and verification
The machine was run in under all operating modes and handed over after technical accuracy checks. It was accepted by the customer.
• The machine was run in and checked in all operating modes;
• Handover to the customer covered completeness, quality, operation and technical accuracy.
The photographs show this actual machine.
16К20 screw-cutting lathe with a distance between centres of 1000 mm.
This is a general-purpose screw-cutting lathe of normal accuracy.
It is designed for a variety of turning operations on metal, plastic and other materials, using three-jaw or four-jaw chucks, centres or collet chucks.
It performs roughing and finishing of external cylindrical and tapered surfaces, hole enlargement and boring, facing and thread cutting, including metric, imperial, module and diametral-pitch threads, in one-off and small-batch production.
Design features following modernization:
• A wide range of spindle speeds and feeds provides productive machining, while the rigid cast bed provides a good surface finish.
• The universal feed gearbox allows metric, imperial, module and diametral-pitch threads to be cut.
• Graduated scales and pointers on the carriage make it easier to determine compound-slide and cross-slide movement during operation. The tool-post design improves clamping stability.
• Special precision spindle bearings require no adjustment during operation, providing the required rigidity and high machining accuracy.
• The gearing of the kinematic chain and the overall machine design provide high reliability.
• The spindle is engaged, disengaged, reversed and braked during operation by a friction clutch without stopping the electric motor.
• The apron has a drop-worm carriage-feed disengagement mechanism for accurate stopping against a fixed stop.
• Modern electrical control components, new wiring and new cable routes improve electrical reliability.
• A 2-axis digital readout improves usability and productivity.
| Machine specifications | 16К20, distance between centres 1000 |
|---|---|
| Accuracy class under GOST 8-82 | H |
| Maximum workpiece diameter accommodated over bed, mm | 400 |
| Centre height above flat bed ways, mm | 215 |
| Maximum machining diameter over carriage, mm | 220 |
| Maximum workpiece length between centres, mm | 1000 |
| Maximum distance from centre axis to tool-post edge, mm | 225 |
| Maximum drill diameter for steel workpieces, mm | 25 |
| Maximum workpiece weight between centres, kg | 460..1300 |
| Maximum workpiece weight in chuck, kg | 200 |
| Spindle | |
| Spindle bore diameter, mm | 52 |
| Maximum bar diameter through spindle, mm | 50 |
| Forward spindle speed, rpm | 12,5..1600 |
| Reverse spindle speed, rpm | 19..1900 |
| Number of forward spindle speeds | 22 |
| Number of reverse spindle speeds | 11 |
| Spindle nose under GOST 12593-72 | 6K |
| Spindle taper bore under GOST 2847-67 | Morse 6 |
| Spindle flange diameter, mm | 170 |
| Maximum spindle torque, N·m | 1000 |
| Feeds | |
| Maximum longitudinal travel, mm | 645, 935, 1335, 1935 |
| Maximum transverse travel, mm | 300 |
| Longitudinal rapid traverse speed, mm/min | 3800 |
| Transverse rapid traverse speed, mm/min | 1900 |
| Maximum permissible travel speed when using stops, mm/min | 250 |
| Minimum permissible carriage travel speed, mm/min | 10 |
| Longitudinal dial graduation, mm | 1 |
| Transverse dial graduation, mm | 0,05 |
| Longitudinal feed range, mm/rev | 0,05..2,8 |
| Transverse feed range, mm/rev | 0,025..1,4 |
| Number of longitudinal feed settings | 42 |
| Number of transverse feed settings | 42 |
| Metric thread pitch range, mm | 0,5..112 |
| Imperial thread pitch range, threads/inch | 56..0,5 |
| Module thread range, module | 0,5..112 |
| Diametral-pitch thread range, diametral pitch | 56..0,5 |
| Maximum longitudinal tool force permitted by feed mechanism, N | 5884 |
| Maximum transverse tool force permitted by feed mechanism, N | 3530 |
| Compound slide | |
| Maximum compound-slide travel, mm | 150 |
| Compound-slide travel per dial graduation, mm | 0,05 |
| Maximum compound-slide swivel angle, degrees | ±90° |
| Compound-slide swivel scale graduation, degrees | 1° |
| Maximum tool shank cross-section, mm | 25 × 25 |
| Height from tool support surface to centre axis (tool height), mm | 25 |
| Number of tools in tool post | 4 |
| Tailstock | |
| Tailstock quill diameter, mm | |
| Tailstock quill taper under GOST 2847-67 | Morse 5 |
| Maximum quill travel, mm | 150 |
| Quill travel per dial graduation, mm | 0,1 |
| Tailstock body transverse offset, mm | ±15 |
| Main drive motor power, kW | 11 |
| Rapid traverse motor power, kW | 0,12 |
| Coolant pump motor power, kW | 0,125 |
| Machine dimensions and weight | |
| Machine dimensions (length width height), distance between centres=1000, mm | 2795 × 1190 × 1500 |
| Machine weight, kg | 3010 |





